The E01 error code on an IFB washing machine indicates that the door is not closed properly.

This can be caused by several things, such as a loose door handle, a broken door latch, or a problem with the door seal. To resolve this problem:

• Start by checking the door handle and latch to ensure they are secure.
• Next, check the door seal to see if it is damaged or not sealing properly. If the seal is damaged, it will need to be replaced. If the door handle, latch, and seal is in good working condition, the problem may be with the door itself. In this case, you will need to call a technician to have the door repaired or replaced.

The E02 error code in an IFB washing machine typically indicates a water supply issue. It suggests that there is either a problem with the water inlet or a lack of water supply to the machine. Here are a few possible causes and solutions for the E02 error code:

• Water supply issue: Ensure that the water supply to the washing machine is turned on and the water pressure is sufficient. Make sure the water taps or valves supplying water to the machine are fully open.
• Clogged water inlet filter: Over time, the water inlet filter can get clogged with debris and restrict water flow. Locate the water inlet hose at the back of the machine and check if the filter is clean. If it's dirty, clean it by removing any accumulated dirt or debris.
• Faulty water inlet valve: If the water inlet valve is faulty, it may not be allowing water to enter the machine properly. In such cases, it is recommended to contact IFB service center or a qualified technician to diagnose and replace the faulty valve if necessary.

The E03 error code in an IFB washing machine typically indicates a draining issue. It suggests that there is a problem with the drainage system, preventing the water from being properly drained. Here are a few possible causes and solutions for the E03 error code:

• Clogged drain filter or pump: The drain filter or pump may be clogged with debris, lint, or other foreign objects. Locate the drain filter and pump (usually located at the bottom front of the machine) and check for any obstructions. Clean the filter and pump if necessary.
• Kinked or blocked drain hose: Ensure that the drain hose is not kinked or blocked. Straighten any kinks and check for any obstructions in the hose that may be hindering the water flow.
• Improper installation of the drain hose: Make sure that the drain hose is correctly installed according to the manufacturer's instructions. It should be properly secured and have a proper air gap to allow for smooth drainage.
• Faulty drain pump or motor: If the above solutions do not resolve the issue, there might be a problem with the drain pump or motor. In such cases, it is recommended to contact IFB service center or a qualified technician to diagnose and replace the faulty component if necessary.

The E04 error code in an IFB washing machine typically indicates a problem with the door lock. It suggests that the door of the washing machine is not closing or locking properly. Here are a few possible causes and solutions for the E04 error code:

• Door not closed properly: Ensure that the door of the washing machine is fully closed and properly latched. Make sure there are no obstructions preventing the door from closing.
• Door lock mechanism issue: The door lock mechanism may be faulty or damaged. Check if the door lock is functioning correctly by attempting to lock and unlock it manually. If it is not engaging or disengaging properly, the lock may need to be replaced.
• Faulty door lock sensor: The door lock sensor, which detects whether the door is closed or not, may be malfunctioning. A faulty sensor can cause the E04 error code. In this case, it is recommended to contact IFB service center or a qualified technician to diagnose and replace the faulty sensor if necessary.
• Wiring or control board issue: There may be a wiring problem or a fault in the control board that is causing the E04 error. These issues require professional inspection and repair, so it is advisable to contact IFB service center or a qualified technician for further assistance.

The E05 error code in an IFB washing machine typically indicates a problem with the water pump. It suggests that there is an issue with the pump motor or its operation. Here are a few possible causes and solutions for the E05 error code:

• Clogged pump filter: The pump filter may be clogged with debris, lint, or other foreign objects. Locate the pump filter (usually located at the bottom front of the machine) and check for any obstructions. Clean the filter if necessary.
• Faulty pump motor: The water pump motor may be faulty or damaged, preventing it from operating properly. In such cases, it is recommended to contact IFB service center or a qualified technician to diagnose and replace the faulty motor if necessary.
• Wiring or control board issue: There may be a wiring problem or a fault in the control board that is causing the E05 error. These issues require professional inspection and repair, so it is advisable to contact IFB service center or a qualified technician for further assistance.

The E06 error code in an IFB washing machine typically indicates a problem with the door lock or its circuit. It suggests that there is an issue with the door lock mechanism, or the electrical connections associated with it. Here are a few possible causes and solutions for the E06 error code:

• Door not closed properly: Ensure that the door of the washing machine is fully closed and properly latched. Make sure there are no obstructions preventing the door from closing.
• Faulty door lock mechanism: The door lock mechanism may be faulty or damaged, preventing it from operating correctly. Check if the door lock is functioning properly by attempting to lock and unlock it manually. If it is not engaging or disengaging as it should, the lock mechanism may need to be replaced.
• Loose or damaged electrical connections: Inspect the electrical connections associated with the door lock. Loose or damaged connections can cause the E06 error. Ensure that all connections are secure and in good condition. If any wires are damaged, they may need to be repaired or replaced.
• Faulty door lock sensor or circuit board: The door lock sensor or the circuit board responsible for detecting the door lock status may be malfunctioning. In this case, it is recommended to contact IFB service center or a qualified technician to diagnose and replace the faulty component if necessary.

If your washing machine is displaying the error code "rin5 HOLD" it means that the machine is not draining properly, implying an error in the drain program. Several things can cause this, but fortunately, there are a few things you can try to resolve the issue.

First, make sure that nothing is blocking the drain hose in your Indian home. If the hose is kinked or there is a blockage in the drain, the water will not be able to flow out of the machine properly.

Next, check the filter. If the filter is clogged, it can also cause the washing machine to have difficulty draining. Be sure to clean or replace the filter if necessary.

If neither of these solutions solves the problem, you may need to call a technician to come and take a look at your machine.

The IFB washing machine dLEr error code indicates that the program selector switch is not in the correct position. This error is usually due to incorrect installation or a loose connection.

To resolve this error, you need to switch off the washing machine, unplug it from the power outlet, and then check the program selector switch. Once you have checked the switch, you can plug the washing machine back in and turn it on. You may need to contact a service technician for further assistance if the error persists.

The "dLAY" error code in IFB washing machines typically indicates a delay in the program. It means that the washing machine is programmed to start the cycle after a specific delay period, and the delay is currently active.

When you encounter the "dLAY" error code, it indicates that the washing machine is waiting for the programmed delay time to elapse before it begins the wash cycle. This is not an error or malfunction; it is a normal operating condition.

If you are experiencing a delay in the start of the wash cycle and it's not intentional, it's possible that the delay feature has been activated by mistake. Refer to your IFB washing machine's user manual to learn how to adjust or deactivate the delay setting.

If you need further assistance or have any concerns about the "dLAY" error code, I recommend contacting IFB service center. They will be able to provide you with specific information and guidance based on the model and features of your IFB washing machine.

The "tAP" error code in IFB washing machines typically indicates an issue with the water supply or water pressure. It suggests that the water supply is insufficient or not reaching the washing machine properly. Here are a few possible causes and solutions for the "tAP" error code:

• Insufficient water supply: Check if the water supply to the washing machine is turned on and the water pressure is adequate. Make sure the water taps or valves supplying water to the machine are fully open.
• Clogged water inlet filter: The water inlet filter can get clogged with debris over time, hindering water flow. Locate the water inlet hose at the back of the machine and check if the filter is clean. If it's dirty, clean it by removing any accumulated dirt or debris.
• Kinked or blocked water inlet hose: Ensure that the water inlet hose is not kinked or blocked. Straighten any kinks and check for any obstructions in the hose that may be hindering the water flow.
• Faulty water inlet valve: If the water inlet valve is faulty, it may not be allowing water to enter the machine properly. In such cases, it is recommended to contact IFB service center or a qualified technician to diagnose and replace the faulty valve if necessary.

This can happen for several reasons, but the most common cause is simply forgetting to switch it off. Other causes can include a power outage or a technical error.

This can usually be resolved by turning off the power to the machine for 30 seconds, then turning it back on and selecting a new program. If the error persists, don't hesitate to contact IBF customer service for further assistance.

If your IFB washing machine displays the error code OFer/Pr5, there is a problem with the program selector. To fix this, you must switch off the program selector and wait 2 seconds before restarting the machine.

There are a few possible reasons for this error code to occur. One possibility is that the program selector is not properly calibrated. Another possibility is that something is blocking the program selector from moving. If you continue to experience this error, it is recommended that you contact a qualified technician for further assistance.

The "dPEr" error code in IFB washing machines typically indicates a problem with the door lock or its circuit. It suggests that there is an issue with the door lock mechanism, or the electrical connections associated with it. Here are a few possible causes and solutions for the "dPEr" error code:

• Door not closed properly: Ensure that the door of the washing machine is fully closed and properly latched. Make sure there are no obstructions preventing the door from closing.
• Faulty door lock mechanism: The door lock mechanism may be faulty or damaged, preventing it from operating correctly. Check if the door lock is functioning properly by attempting to lock and unlock it manually. If it is not engaging or disengaging as it should, the lock mechanism may need to be replaced.
• Loose or damaged electrical connections: Inspect the electrical connections associated with the door lock. Loose or damaged connections can cause the "dPEr" error. Ensure that all connections are secure and in good condition. If any wires are damaged, they may need to be repaired or replaced.
• Faulty door lock sensor or circuit board: The door lock sensor or the circuit board responsible for detecting the door lock status may be malfunctioning. In this case, it is recommended to contact IFB service center or a qualified technician to diagnose and replace the faulty component if necessary.

The "HEAt" error code in an IFB washing machine typically indicates a problem with the heating system. It suggests that the washing machine is unable to reach the desired temperature during a specific cycle or that there is an issue with the heating element or related components. Here are a few possible causes and solutions for the "HEAt" error code:

• Incorrect temperature setting: Ensure that you have selected the appropriate temperature setting for the desired wash cycle. If the selected temperature is too high or too low for the available water supply, the error code may be triggered. Adjust the temperature setting accordingly.
• Faulty heating element: The heating element in the washing machine may be faulty or damaged, preventing it from heating the water properly. In such cases, it is recommended to contact IFB service center or a qualified technician to diagnose and replace the faulty heating element if necessary.
• Wiring or control board issue: There may be a wiring problem or a fault in the control board that is causing the "HEAt" error. These issues require professional inspection and repair, so it is advisable to contact IFB service center or a qualified technician for further assistance.

If your washing machine is experiencing the error code ACHi, the machine is restarting automatically after the voltage decreases. There are a few reasons why this error code may occur, and fortunately, there are also a few ways to fix it.

A faulty water inlet valve is the most common reason for this error code. The water inlet valve regulates the water flow into the washing machine, and if it is not working properly, the machine will automatically restart once the water pressure drops.

Another possibility is that the washing machine's pressure switch is not functioning correctly. The pressure switch is responsible for detecting when the water level in the machine is too low, and if it is not working properly, the machine will restart to increase the water level.

The "ACLo" error code in an IFB washing machine typically indicates an issue with the water supply. It suggests that the water supply is either too low or completely absent. Here are a few possible causes and solutions for the "ACLo" error code:

• Insufficient water supply: Check if the water supply to the washing machine is turned on and the water pressure is adequate. Make sure the water taps or valves supplying water to the machine are fully open. If the water pressure is too low, you may need to improve the water supply or consult a plumber to address the issue.
• Clogged water inlet filter: The water inlet filter can become clogged with debris over time, obstructing water flow. Locate the water inlet hose at the back of the machine and check if the filter is clean. If it's dirty, clean it by removing any accumulated dirt or debris.
• Kinked or blocked water inlet hose: Ensure that the water inlet hose is not kinked or blocked. Straighten any kinks and check for any obstructions in the hose that may be hindering the water flow.
• Faulty water inlet valve: If the water inlet valve is faulty, it may not be allowing water to enter the machine properly. In such cases, it is recommended to contact IFB service center or a qualified technician to diagnose and replace the faulty valve if necessary.

If your IFB washing machine displays the error code H260, it means a high voltage issue with the machine. Several things can cause this error, but the most common cause is a problem with the washing machine's power supply.

There are a few different ways to solve this problem, but the most common solution is simply resetting the machine. You'll need to unplug the machine from the power outlet and then plug it back in. Once the machine is plugged back in, the error code should be cleared, and the machine should be able to function properly.

The "UnbL" error code in an IFB washing machine typically indicates an unbalanced load. It means that the laundry inside the machine is not distributed evenly, causing an imbalance during the spin cycle. Here are a few possible causes and solutions for the "UnbL" error code:

• Overloading the machine: If the washing machine is overloaded with too much laundry, it can result in an unbalanced load. Make sure to follow the recommended load capacity mentioned in the user manual and avoid overloading the machine.
• Uneven distribution of laundry: Ensure that the laundry is distributed evenly inside the machine. Unevenly placed or tangled clothing can lead to an unbalanced load. Arrange the items in a balanced manner, spreading them out as evenly as possible.
• Large and heavy items: Bulky or heavy items such as blankets, comforters, or rugs can cause an unbalanced load. Try redistributing the weight by adding other items to create a more balanced load.
• Malfunctioning suspension system: If the machine consistently displays the "UnbL" error code even with a properly balanced load, there may be an issue with the suspension system. In such cases, it is recommended to contact IFB service center or a qualified technician to diagnose and repair the problem.

During an "UnbL" error, the washing machine may stop or pause the cycle to prevent damage from the unbalanced load. Once you have adjusted the load to be more balanced, you can try restarting the machine or selecting a spin-only cycle to allow it to complete the cycle.

The "L175" error code in IFB washing machines typically indicates an issue with the water level or water filling process. It suggests that the water level is not reaching the desired level within a specified time. Here are a few possible causes and solutions for the "L175" error code:

• Insufficient water supply: Check if the water supply to the washing machine is turned on and the water pressure is adequate. Make sure the water taps or valves supplying water to the machine are fully open. If the water pressure is too low, you may need to improve the water supply or consult a plumber to address the issue.
• Clogged water inlet filter: The water inlet filter can become clogged with debris over time, obstructing water flow. Locate the water inlet hose at the back of the machine and check if the filter is clean. If it's dirty, clean it by removing any accumulated dirt or debris.
• Kinked or blocked water inlet hose: Ensure that the water inlet hose is not kinked or blocked. Straighten any kinks and check for any obstructions in the hose that may be hindering the water flow.
• Faulty water inlet valve: If the water inlet valve is faulty, it may not be allowing water to enter the machine properly. In such cases, it is recommended to contact IFB service center or a qualified technician to diagnose and replace the faulty valve if necessary.
• Water level sensor issue: The water level sensor, which detects the water level inside the machine, may be malfunctioning. If the sensor is not accurately detecting the water level, it can trigger the "L175" error. Contact IFB service center or a qualified technician to diagnose and repair the water level sensor if needed.

The "door" error code in an IFB washing machine indicates a problem with the door or its related components. It suggests that there is an issue with the door lock, latch, or the electrical connections associated with it. Here are a few possible causes and solutions for the "door" error code:

• Door not closed properly: Ensure that the door of the washing machine is fully closed and properly latched. Make sure there are no obstructions preventing the door from closing. Sometimes, the error may be triggered if the door is not closed securely.
• Faulty door lock mechanism: The door lock mechanism may be faulty or damaged, preventing it from operating correctly. Check if the door lock is functioning properly by attempting to lock and unlock it manually. If it is not engaging or disengaging as it should, the lock mechanism may need to be replaced.
• Loose or damaged electrical connections: Inspect the electrical connections associated with the door lock. Loose or damaged connections can cause the "door" error. Ensure that all connections are secure and in good condition. If any wires are damaged, they may need to be repaired or replaced.
• Door lock sensor or circuit board issue: The door lock sensor or the circuit board responsible for detecting the door lock status may be malfunctioning. In such cases, it is recommended to contact IFB service center or a qualified technician to diagnose and replace the faulty component if necessary.
• Faulty door latch: If the door latch itself is damaged or broken, it may prevent the door from closing properly and trigger the "door" error code. If this is the case, the door latch may need to be replaced.

To use the Tub Clean mode in an IFB washing machine, follow these steps:

• Ensure the drum is empty: Remove any clothes or items from the IFB washing machine drum.
• Check the detergent dispenser: Make sure the detergent dispenser is clean and free of any detergent or fabric softener residue. If needed, clean the dispenser using warm water and a mild detergent.
• Add cleaning agent: IFB washing machines often come with a specific tub cleaner or descaling powder provided by the manufacturer. Refer to the user manual or check the IFB website for the recommended cleaning agent. Follow the instructions on the packaging to determine the appropriate amount to use.
• Load the cleaning agent: Open the detergent dispenser or follow the specific instructions for your IFB model to load the cleaning agent. Some machines have a designated slot for the tub cleaner, while others may require you to add it directly into the drum.
• Select the Tub Clean mode: Locate the control panel on your IFB washing machine. Look for a button or a specific program labeled "Tub Clean" or "Drum Clean." Press the button or select the program to activate the Tub Clean mode.
• Adjust settings (if necessary): Depending on the model, you may have the option to adjust settings such as water temperature and duration of the Tub Clean cycle. Follow the user manual or on-screen instructions to select the desired settings.
• Start the Tub Clean cycle: Once you have selected the Tub Clean mode and adjusted the settings, press the "Start" or "On" button to begin the cycle. The washing machine will fill with water and run a specialized cleaning cycle to remove residue, odors, and mineral deposits from the drum and other internal components.
• Allow the cycle to complete: Let the Tub Clean cycle run its course until it finishes. The duration of the cycle will vary depending on the IFB model and the specific settings you have chosen.
• Wipe the drum and door seal: After the Tub Clean cycle is complete, open the door and inspect the drum and door seal. Use a damp cloth to wipe away any remaining residue or cleaning agent.
• Air out the machine: Leave the washing machine door open for some time to allow the drum to dry completely. This helps prevent the growth of mold or mildew.